Use less text on mobile! Call attention to a special discount, feature, or promotion here.
Home / NEWS

NEWS

How to use and maintain the swimming pool cleaning machine

How to use and maintain the swimming pool cleaning machine
The swimming pool cleaning machine, also known as the pool stain absorption machine. Many people like to call the machine cleaning pool cleaning machine, but because the machine of the cleaning pool is mainly a swimming pool absorbing machine, from a narrow perspective, it is also the swimming pool. Swetting machine. This article focuses on the use and maintenance of swimming pool absorbers:
There are two types of swimming pool cleaning machines: fully automatic swimming pool containment machine, manual swimming pool dirt absorbers (also known as shore base swimming pool dirt absorbers, combined dirt absorbers). The two types of dirt absorbers have their own characteristics, and the occasions they use are different.
The full automatic polluting machine of the swimming pool cleaning machine: When the sewage is absorbed, the water flows into the bottom and immediately flows out of the upper part of the machine, so that the water of the swimming pool cannot be restrained. The machine, because the water cannot remain static, the precipitation will rise. To this end, the swimming pool using an automatic dirt absorption machine must be equipped with a better circulating filtering system.
The manual polluting machine of the swimming pool cleaning machine: its advantages are light, convenient, clean, good safety, good safety, stable quality; it is divided into pushing rod type and ropes. 5 meters or 8 meters, use the stain on the other side, and the width of the swimming pool should not exceed 15 meters. If it exceeds, you can choose a rope pull -ups. It is applicable to standard swimming pools.
The maintenance of the swimming pool cleaning machine must be achieved:
a. View and clean the sand cylinder regularly: The sand cylinder should be kept clean, so that the dirt absorbers can maintain performance.
b. Regularly check the pump head cover sealing ring. If it is damaged, replace it in time.
c. Keep the motor cleaning and keep the motor open.
d. In accident, the axis sealing ring of the motor will be worn and should be replaced in time.
Generally, the dirt absorbers are used in the summer. When it is not used in winter, water should be removed in the pump head, cleaning the inside and outside of the pump, and placing the water pump in a dry and ventilated room. Only in this year can maintain good performance.

Cleaning method of swimming pool

Cleaning method of swimming pool
Generally, the remaining outdoor pool with normal water quality should be maintained at 0.3-0.5 mg/L, and the pH value is maintained at 7.4-7.6. In this environment, bacteria and algae are not easy to grow and reproduce. After continuous rain and snow, the remaining chlorine in the water will generally not reach the standard, and the pH of the water will have room for bacteria and algae. Moreover, the spores, lawn and soil when it rains will bring algae into the water body when entering the water body. Then, when the water temperature of the summer swimming pool is high (usually 28-30 degrees), the bacteria and algae will quickly reproduce, so The water in the swimming pool turns green in a short period of time.

So how do you solve this problem? Specifically divided into the following steps for operation:

1. First of all, you must add copper sulfate. The general amount of addition is 1-2 times that of usual. This is because there are very few algae in the water, and a large amount of algae exists after the water is green. Copper) can fully kill algae. After adding algae kill agents (copper sulfate), the swimming pool water circulation system should be opened to allow the pharmaceutical agent to be as uniform as possible in the water, so as to achieve the best effect;

2. After about 2 hours, add trichlorolyloropatoly uric acid disinfection agent. Treatment or ultra chlorine treatment to make the water of the swimming pool sufficient sterilization and disinfection;

3. After about 2 hours, the pH value of the water detection is usually rained and the use of trichlorolyllorolyuronic acid disinfection agents. The pH value of the water will definitely be low. Therefore ) It can increase the pH value of the water. The amount of holiday is to increase the amount of addition by 1 degree per 1,000 cubic meters of water. It is best to adjust the pH value to 7.5;

4. In the evening holiday precipitant, the amount of addition is based on 5-8kg of 5-8kg per 1,000 cubic meters, so that the small algae and other suspended substances that have been killed in the water can be precipitated to the bottom of the pool; the analysis comes from Shangshui Environmental Technology.

5. The sediment at the bottom of the pool was used to take away the sediment at the bottom of the pool the next day.

Effective method of water quality treatment of swimming pools

Effective method of water quality treatment of swimming pools
1. Cleaning the pool

After a long period of vacancy in the swimming pool, moss will be on the wall, so the swimming pool must be completely cleaned in front of the water. It is recommended to use a special swimming pool cleaning agent to completely remove the moss in growth, otherwise it is easy to regenerate after the release of the water, so it is difficult to completely remove it in the later period.

2. Kill algae suppress algae

When the new water starts to enter the pool, as long as there is a small part of the water in the pool, they will immediately put the algae killer, calculate the increase according to the total amount of water in the swimming pool, and add it at a time (2kg every 1,000 cubic cubic cubic cubic meters, when the addition, the water is used, the water is used, and the water is used. Dilute algae sterilizer and spray evenly).



3. Disinfection and sterilization

When the new water is filled, the disinfection powder or disinfection tablets are added for disinfection, and the amount of water is calculated according to the total water volume of the swimming pool. Sprinkle directly into the swimming pool.

4. PH adjustment

After filling the new water (if it is not full on the day, within 3 hours after adding the swimming pool disinfection agent), test the pH value. If it is less than 7.2, you need to add a pH regulator to 7.2-7.6, add the plus investment, and add it to the investment. The amount of 1000 cubic meters and 10kg can be increased by 1 degree.

5. Water purification treatment

After completing the above steps, you can add a clarified agent for clarification. Add 1kg of 1kg for each 1,000 cubic meters to calculate the amount. Dilute the clearing agent and sprinkle it in. At this time It is through the adsorption of salt particles to form a large particle in the water to form a large particle, so that it enters the circulation system with the flow of the water, and finally filter the water through the sand cylinder to make the water clean.



In fact, instead of adding the water quality processing through the addition of disinfection agents, it is better to put circular filtration and backwash steps in the design through the use of water flow dynamic and scientific design in the early stage. The rinse design, and then use AFM active filter materials to replace quartz sand, using its self -disinfection ability, so that bacteria loses the place where survival, so as to solve the problem of water quality from the root cause, while reducing the dependence on disinfection agents.